Bass Boat Technologies - Ranger RT 178/188/198

Please read ALL notes on the pages of the mount that you are looking to purchase, this will save mis-ordered mounts from being shipped and prevent you from having to re-order and then return the wrong product.

2020+ Ranger RT Bow
2024+ Ranger Alpha Bow

If your bow looks like this, then this mount will fit.

This mount will include LEVELER "B"

New: There is now an option in the dropbox to get either the "Standard Stack Top" or "Off-Set Right" Stack Top. The "Offset Right" tops are designed to shift both units to the right 2 inches allowing for better control of the Trolling Motor Cables, especially the Garmin Force TM and Lowrance Ghost TM large cables.

These will fit any Dual Stack mount from BBT.

See Example Pics. We will send the correct Top to fit what Boat Model you are buying for on the order.

$375.00

Option A (2018 and under)
Option B (2019 +)
Option C (2020+ models)
Option D - ALPHA 208 (2024+)

For Option A - RT - If you have this dash, and you order a Dual Dash Mount, the two smaller gauges will be moved down into our plate.

For Option B - RT - The gauges will stay in the current position. A backer plate is REQUIRED for this mount and an additional $35.00 will be added to the price.

For Option C - RT - The gauges will stay in the current position. A backer plate is REQUIRED for this mount and an additional $35.00 will be added to the price.

For Option D - ALPHA 208 - A backer plate is REQUIRED for this mount and an additional $35.00 will be added to the price.

This mount allows you to move your 2 - small gauges down to bottom of mount plate to be able see them and kit includes 2 - snap-in small gauge hole covers

2016 and Earlier RT Models - Your Steering wheel should have 6 screws that hold it in place. A 2 1/2" Steering Wheel spacer will be required for this mount system, which can be purchased here.

2017 + RT Models - Ranger changed the steering wheel to a 1 piece Steering Wheel/ Cog. If yours boat has Hydraulic Steering, then your steering wheel should measure from the dash to the inside top edge of steering wheel, it should read about 6 3/8 - 6 5/8", If that is the case, then no spacer should be needed in most cases. If it is 4" on that measurement, then you will need a complete changeover kit to be able to add a spacer to increase area between steering wheel and unit. Steering Wheel Changeover Kit can be purchased here.

You will need to contact Bass Boat Technologies for all other units to be mounted.

Please note: If you have a current sonar/gps unit mounted in the dash, please list in the box below. If there was no unit mounted in dash, please write "none".

If you have larger units that are not listed in the drop down menu for GPS/Sonar, then go to the RT178 / RT188 / RT198 - Dual MEGA Mount

$405.00

Option A (2018 and under)
Option B (2019 +)
Option C (2020+ models)
Option D - ALPHA 208 (2024+)

For Option A - RT - If you have this dash, and you order a Dual Dash Mount, the two smaller gauges will be moved down into our plate.

For Option B - RT - The gauges will stay in the current position. A backer plate is REQUIRED for this mount and an additional $35.00 will be added to the price.

For Option C - RT - The gauges will stay in the current position. A backer plate is REQUIRED for this mount and an additional $35.00 will be added to the price.

For Option D - ALPHA 208 - A backer plate is REQUIRED for this mount and an additional $35.00 will be added to the price.

2016 and Earlier RT Models - Your Steering wheel should have 6 screws that hold it in place. A 2 1/2" Steering Wheel spacer will be required for this mount system, which can be purchased here.

If you have a current sonar/gps unit mounted in the dash, please list in the box below. If there was no unit mounted in dash, please write "none".

Disclaimer: The Apex Factory Gimbal brackets have a Hole Pattern in them that "Does Not" match any previous hole pattern used by Humminbird in the past. We will send a Hole pattern with mounts that have a Apex model graph and you will need to mark your factory Apex gimbal Bracket and drill 9/32 holes them to match our pattern.

Note: The BBT Cheyenne Series Apex Gimbal Brackets will have the same hole pattern in them as Helix and Solix Gimbal Brackets.

If you have smaller units that are not listed in the drop down menu for GPS/Sonar, then go to the RT178 / RT188 / RT198 - Single Mount

$405.00

Option A (2018 and under)
Option B (2019 +)
Option C (2020+ models)
Option D - ALPHA 208 (2024+)